Reasons Your Fiat 500 Key Fob Won't Work
A
fiat car key 500 key fob is a great way to unlock the doors and get started the car. There are many reasons why the key fob might stop working. This could be due to a dead coin battery, damage to the receiver module, water issues, or interference.
This listing is for an NEW replacement
fiat 500x Key fob programming Flip Key Remote - like the Ilco brand that must be professionally programmed by a local automotive locksmith (click here for Locksmith Search). Includes trunk, lock and unlock buttons.
Dead Coin Battery
A dead battery is the most common reason for your 500 key fob that isn't working. Modern key fobs have a very limited operating range and should be within a few feet of the car to operate. If you are far from your vehicle and you press the keyfob button it won't respond and display the message "Key Fob Not Detected".
If this happens, replace the battery in the coin cell (Part number CR2032) with a brand new one from a reputable manufacturer like Panasonic, Duracell, or Energizer. They are typically available in your local hardware store or on the internet.
You can test the battery on your coin-cell by pressing the buttons while standing near your Fiat 500. The car should blink its parking lights and the key fob should work the lock and unlock switches.
If your key fob isn't working after replacing the battery, there may be water damage which is preventing it from interacting with the module in your vehicle. Water damage can occur in a variety of ways, ranging from an accidental splash to submerging the fob in salt water at the beach. If you suspect that your fob was exposed to water, you can place it in a rice bag to draw out the moisture. If this doesn't work, the fob might require reprogramming by an experienced auto locksmith or dealer.
Water Damage
Damage to the water supply can occur if you immerse the fob into the ocean or wash it in a machine. Saltwater poses a particular risk to the fob's circuit board which causes it to short out and eventually die. It's not the best idea to soak the fob in water however, but don't give it up in the event that you accidentally drop it in water or
[Redirect-302] fail to take it out of your pocket.
Remove the battery first. Before replacing the battery clean the electronic chip using isopropyl or a similar product. Then try the fob and
fiat panda remote Key replacement check if it functions. If the key does not function, it may need to be programmed again. This is usually handled by an auto locksmith or dealer.
If your key is old and has not been programmed to work with your vehicle it is necessary to replace it completely. A professional locksmith in the automotive industry will be able to complete this process. The locksmith will need the key to be cut to match your car's ignition. They'll also have to reprogram the fob in your vehicle's system. This is a low-cost and quick procedure that can be completed on the same day.
Receiver Module Issues
The 500 key fob could not function because it's out of range. The remote has a range of 30 feet, which means if you are too far from your car it won't be able to respond to your commands. This can easily be resolved by moving it closer to your vehicle until it starts responding.
If your fob isn't working after you replace the battery inside the coin, which is also called a "button", "watch" or "button" it may be due to a malfunction on the internal circuit board. In the majority of cases, reprogramming your fob can resolve the problem. You can find instructions on how to do this for all vehicles by searching YouTube or looking through the owner's manual.
It is possible to replace the metal clips that hold the coin batteries in their place. If they become loose, it can stop your coin battery from being properly seated, causing your remote to malfunction.
In rare instances, the fob might be out of alignment with your vehicle because due to hardware or software issues. This can be a major headache, but you can usually fix it by visiting a local dealer or auto locksmith to have them reprogram your fob. In some instances, the software may also require reinstallation in your body control modules.
Interference
In addition to a dead coin battery The key fob might not be receiving or transmitting an signal due to interference. This could occur if the key fob is in close proximity to a radio transmitter such as a cell phone or radar detector. The key fob may not function due to a poor connection with the buttons water damage or damage to the internal chips.
If the key fob has stopped working one day in the middle of the night and you've tried everything you can do at home to resolve it e.g. You could have a malfunctioning 500 receiver module in the event that you've tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module is located under the dash and picks up the radio frequency signals from the key fob. It converts the signals into electronic commands, which are then read by the vehicle.
There is a straightforward method to reset the 500's in-board system, including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Reconnect the battery. This will get rid of any remaining electricity and then restart the car's computer system, which could allow you to the key fob to function again. If the issue persists, you should consult an expert technician. They will be able diagnose the exact cause of any issues.